€147.61
pcs
Properties
Po­si­tion drive di­men­sions 20
Flange drilling screen F03
Swivel angle [deg] 90
Ad­justable range end po­si­tion at 0° [deg] -5 to 5
Ad­justable range end po­si­tion at 90° [deg] -5 to 5
Shaft con­nec­tion Depth [mm] 10
Stan­dard con­nec­tion to fit­ting ISO 5211
in­stal­la­tion po­si­tion ar­bi­trary
Prin­ci­ple of op­er­a­tion sin­gle ac­tion
Con­struc­tion set up Toothed rack/pin­ion
Clos­ing di­rec­tion Right clos­ing
Valve con­nec­tion cor­re­sponds to stan­dard VDI/VDE 3845 (NAMUR)
Con­nec­tion for po­si­tion con­trollers and po­si­tion feed­back sig­nal com­ply with stan­dard VDI/VDE 3845 Size AA 1
Safety In­tegrity Level (SIL) Pro­dukt kann einge­setzt wer­den in SRP/CS bis SIL 2 High De­mand
Op­er­at­ing pres­sure [bar] 2 to 8
Nom­i­nal op­er­at­ing pres­sure [bar] 6,0
CE cer­tifi­cate (see de­c­la­ra­tion of con­for­mity) to EU EX pro­tec­tion di­rec­tive (ATEX)
Cer­ti­fied award­ing point TÜV Rhineland
ATEX gas cat­e­gory II 2G
ATEX dust cat­e­gory II 2D
Ex ig­ni­tion pro­tec­tion type gas Ex h IIC T4 Gb X
Ex ig­ni­tion pro­tec­tion type dust Ex h IIIC T105°C Db X
Ex am­bi­ent tem­per­a­ture -20°C <= Ta <= +80°C
Op­er­at­ing medium Com­pressed air to ISO 8573-​1:2010 [7:4:4]
In­for­ma­tion about op­er­at­ing and con­trol medium Oiled op­er­a­tion pos­si­ble (re­quired in fur­ther op­er­a­tions),
Pres­sure dew point 10°C under am­bi­ent and medium tem­per­a­ture
Bear­ing tem­per­a­ture [°C] -20 to 60
am­bi­ent tem­per­a­ture [°C] -20 to 80
Ro­tary torque for nom­i­nal op­er­at­ing pres­sure and 0° pivot angle [Nm] 14,7
Ro­tary torque for nom­i­nal op­er­at­ing pres­sure and 90° pivot angle [Nm] 7,6
In­for­ma­tion about torque The op­er­at­ing torque of the ac­tu­a­tor may not be higher than the max­i­mum per­mit­ted torque listed in ISO 5211, re­lated to the size of the fas­ten­ing flange and the cou­pling.
Air con­sump­tion a 6 bar per cycle 0°-90°-0° [LTR] 0,8
Prod­uct weight [g] 1.419
Shaft con­nec­tion T9
Pneu­matic con­nec­tion G1/8
Ma­te­r­ial in­for­ma­tion RoHs com­pli­ant
Con­nec­tion plate ma­te­r­ial Alu­minium wrought alloy, an­odised
Cover ma­te­r­ial Alu-​Druckguss, beschichtet
Seals ma­te­r­ial NBR
Hous­ing ma­te­r­ial Alu­minium wrought alloy, an­odised
Pis­ton ma­te­r­ial Alu­minium die cast­ing
Bear­ing ma­te­r­ial POM
Lug ma­te­r­ial Cast stain­less steel
Screws ma­te­r­ial High-​alloyed stain­less steels
Shaft ma­te­r­ial High-​alloyed stain­less steels
Spring force torque at a swivel angle 0° [Nm] 7,2
Spring force torque at 90° [Nm] 14,3
Spring ma­te­r­ial spring steel
Further information on OT-FESTO070916
Weight 1.419 g / pcs
Customs duty number 84123900
Manufacturer Festo
Documents

 
All data are to be understood as non-binding reference values! We do not assume liability for any data selection not confirmed in writing. Unless otherwise specified, pressure values refer to liquids from Group II at +20°C.
Immediately available